Cherry Mobile Ace 2 V2.0 Firmware / Stock Rom

Cherry Mobile Ace 2 V2.0 firmware
Cherry Mobile Ace 2 V2.0

Here is the updated and tested official firmware for your Cherry Mobile Ace 2 V2.0, This is SPD Chip so the firmware is PAC file, ready to flash in free software like ResearchDownload or Upgrade Download.




Why we flash a new firmware for Cherry Mobile Ace 2 V2.0? Here are common software problem of android phone that can be fix through flashing new firmware, and remember that flashing can only fixed software problem, this firmware is tested and here are the following software problem that can be fix in flashing new firmware:
  • Cherry Mobile Ace 2 V2.0 Infected Virus - Also known as Monkey Virus where when you connect to Internet, there is automatically download apps or some popup screen and sometimes automatically turn on WiFi or data connection without doing it. The virus will not remove though hard reset or formatting your phone. Installing new firmware is the best solution.
  • Cherry Mobile Ace 2 V2.0 Unfortunately Error - This is when you open some apps it will popup Unfortunately, App has stopped. If cannot fixed through clearing the data, then flashing new firmware is also the solution.
  • Cherry Mobile Ace 2 V2.0 Stuck or Hang in Logo - The reason for this is either when you install incorrect Rom. Try to hard reset first but if still stuck, then flashing firmware is also the solution
  • Cherry Mobile Ace 2 V2.0 boot loop.

Download Cherry Mobile Ace 2 V2.0 Firmware / Stock Rom
Password: 
gsmbiboy

Thanks and credit to gsmbiboy


Flashing Stock Rom To Android Smartphone

Install Spreadtrum Driver

  1. First download SPD SCI Android USB Driver V4 by jungo the complete driver for Spreadtrum.
  2. After download, extract anywhere  in your computer, Open extracted SCI-android-usb-driver-jungo-v4 folder then select system type if 32-bit or 64-bit.
    - To know your system type, go to control panel click on System and Security then click System. or simply right click on Computer and click Properties. you will see like this. mine is 32 bit (also known as x86-bit).
    System Type 32-bit operating system
  3. Then run DPInst.exe. Just click next until it finish installing.
    SCI-android-usb-driver-jungo-v4 driver
NOTE: Before proceeding, make sure that your android smartphone should have atleast 30 to 50 percent of battery to perform flashing.


Flash Pac file Stock Rom

  1.  Download the SPD_Upgrade_Tool_R4.0.0001 latest version, or SPD_Upgrade_Tool_R299015 lower version. Then extract to your desired location.
  2. Open your extracted files and run ResearchDownload.exe, For lower version open Bin folder and run UpgradeDownload.exe.
    NOTE:
    UpgradeDownload and ResearchDownload is the same, UpgradeDownload is just the name of the lower version but they are both SPD Upgrade tool.
    UpgradeDownload.exe
  3. In this instruction I will use UpgradeDownload and a Use Cherry Mobile Pac file as a sample. In UpgradeDownload window, click on single gear icon to Load Packet and browse for pac file(firmware/stock rom) you downloaded then click open. follow this screenshot.
    UpgradeDownload Load Packet
  4. Loading a pac file may took long depend on file size. After loading a pac file, now ready to start flashing, You can also click on Settings on two gear icon if you want to unchecked some part of firmware like EraseRuntimeNV, This will not work on lower version. I recommend that leave it unchanged if you don't have any idea.
    UpgradeDownload Start Downloading
  5.  Turn off first your phone, remove battery (if removable) then bring it back. In ResearchDownload/UpgradeDownload Click on Start Downloading, then in your phone press Volume up and Volume down then connect USB cable. If you see a a progress bar, then it means that it is successfully connected. if not, then try step 5 again.
    UpgradeDownload start


  6. Wait until you see a Passed in progress, that means, you installed a new stock rom successfully.
After you flash the firmware, you can now turn on your phone, take note that first time start up may took long. but if it took more than 15 minutes then I suggest to perform a hard reset.

31 comments:

  1. thanks for sharing...sana gumana po sa c.m ace 2 v2.0 ko keep up

    ReplyDelete
  2. sir bat ayaw po ma mag install ng device ko na install kuna man po ng maayos yong driver...sana may makasagot po.. god bless

    ReplyDelete
    Replies
    1. Follow mo lang instruction boss1, make sure ok usb cable and port ng cp mo

      Delete
  3. sir. success po. pwede nyo po ba ako tulungan? need ko daw i log in dating naka log in na google sa cp ko para magamit ko uli. ang problema wala na ung goggle acc. ko na yun kaya diko na ma-open cp ko. help boss plss. message nyo po ako sa FB boss need ko tlga maayos cp ko. FB - https://www.facebook.com/JoepheeTanedo?fref=nf maramiing salamat bossing. (Y)

    ReplyDelete
    Replies
    1. follow lang po ito, para sa bypass ng CM ace 2 frp http://www.gsmsolutionph.com/2017/03/cherry-mobile-ace-2-frp-verify-account.html

      Delete
  4. sir mag start nd process bar...wla aqng mkita kahit sinunud q na lahat ng procedure...patolong po...

    ReplyDelete
  5. sir ayaw mag start ng process bar...wla aqng mkita kahit sinunud q na lahat ng procedure...patolong po...

    ReplyDelete
    Replies
    1. tamang timing lang sir, make sure naka install maayos ang driver.

      Delete
  6. Sir bakit po nag fail send uart error

    ReplyDelete
    Replies
    1. Check mo bro kung naInstall ng maayos yung driver or change cable.

      Delete
  7. Di ko mainstall ang MTP USB Device Driver. Failed parati. pa help nman.

    ReplyDelete
  8. ayaw gumana!!!!

    ReplyDelete
  9. boss thanks sa firmware

    ReplyDelete
  10. failed in FDL2 .it says Device unplugged
    nagtry na ako ng ibat ibang cable not working parin.
    pa help mga boss

    ReplyDelete
    Replies
    1. try mo Timing ng pag insert ng usb bro, restart pc or try other pc din if necesarry.

      Delete
    2. nagtry na rin ako boss. ganun din sa ibang pc..

      Delete
  11. master failed: Uart send error yong nangyayari sa akin lagi na install ko naman yong drivers FDL Checking baudrate lagi tapos after 9 seconds error na ayaw dumiritso....please help master

    ReplyDelete
  12. Malalaman kung hardware ang problema nya base sa history, example, Nabasa ng tubig, then namatay in few days, hardware problem yun. kung nag hahang lang then nireprogram mo at after mareprogram namatay na, thats a software problem

    ReplyDelete
  13. BAkit dko po ma DL ung stock rom ? Ung search Extension lang po lumalabas ?

    ReplyDelete
  14. ganun parin sir. almost 6mos din kasi nastock yung phone sa pagkakabootloop.
    nagrereconnect after 6s uart device unplugged
    any suggestion?

    ReplyDelete
    Replies
    1. Una dapat naka Charge yung batt atlease 50%, then yung driver installed dapat, yung usb cable working dapat at wag gagalawin habang nag flaflash.

      Delete
  15. icoconvert pa ito sa .pac file eh

    ReplyDelete
  16. Replies
    1. The given driver above is working on windows 7 32bit. either search for windows 7 or search driver for your device.

      Delete
  17. tnx gsmbiboy successful flashing cherry mobile ace2 v2.0

    ReplyDelete